TurnCutParameters Class¶
-
class
NXOpen.CAM.
TurnCutParameters
¶ Bases:
NXOpen.CAM.CutParameters
Represents a
NXOpen.CAM.TurnCutParameters
New in version NX6.0.0.
Properties¶
Property | Description |
---|---|
AdditionalProfiling | Returns or sets the additional profiling |
AllowUndercut | Returns or sets the undercut |
CheckIpwCollisions | Returns or sets the value to Check for Ipw Collsions |
CheckSafeClearance | Returns the Check Safe Clearance |
ChipControl | Returns the chip control |
CleanupControl | Returns or sets the cleanup control |
ConcaveCornerControl | Returns the corner concave |
ContourDiameterAngle | Returns the contour diameter angle |
ContourFaceAngle | Returns the contour face angle |
ContourLevelAngle | Returns the contour level angle |
ContourSteepAngle | Returns the contour steep angle |
CutConnection | Returns or sets the cut connection |
CutDwell | Returns the Cut Dwell |
CutFillets | Returns or sets the fillets mode |
ExtendAtStart | Returns or sets the Corner Start Extension |
FacesSequence | Returns the Faces Sequence |
FinishDwell | Returns the finish dwell |
FinishPasses | Returns or sets the finish passes |
GrooveCornerControl | Returns the groove corner control |
HolderClearance | Returns the Holder Clearance |
InitialProfilePlunge | Returns the initial profile plunge |
IpwType | Returns or sets the IPW type |
MinCutDepth | Returns the min cut depth |
MinCutLength | Returns the min cut length |
MultiPasses | Returns the multi passes |
MultiRamp | Returns the multi ramp |
NeckClearance | Returns the Neck Clearance |
NormalCorner | Returns the normal corners |
OmitLastPass | Returns or sets the omit last pass |
PartSafeClearance | Returns the Part Safe Clearance |
PartStock | Returns the part stock |
ProfileCutRegions | Returns or sets the profile cut regions |
ProfileDirection | Returns the direction |
ProfileStrategy | Returns the cut strategy |
RampingMode | Returns the ramping mode |
ReliefCut | Returns the relief cut |
ReliefPlunge | Returns the Relief Plunge |
SecondaryTestCut | Returns the Secondary Test Cut |
ShallowCorner | Returns the corner shallow |
ShankClearance | Returns the Shank Clearance |
SpringPasses | Returns the spring passes |
StopPosition | Returns the stop position |
Tag | Returns the Tag for this object. |
TestCut | Returns the Test Cut |
Tolerances | Returns the Tolerances builder |
TurnBlankStock | Returns the blank stock |
TurnCutterClearance | Returns the cutter clearance angles |
TurnOverlap | Returns the overlap |
TurnPartStock | Returns the part stock |
TurnProfileStock | Returns the profile stock |
UseToolHolder | Returns or sets the use tool holder |
Methods¶
Property Detail¶
AdditionalProfiling¶
-
TurnCutParameters.
AdditionalProfiling
¶ Returns or sets the additional profiling
-------------------------------------
Getter Method
Signature
AdditionalProfiling()
Returns: the additional profiling Return type: bool New in version NX6.0.0.
License requirements: None.
-------------------------------------
Setter Method
Signature
AdditionalProfiling(profilingValue)
Parameters: profilingValue (bool) – the additional profiling New in version NX6.0.0.
License requirements: cam_base (“CAM BASE”)
AllowUndercut¶
-
TurnCutParameters.
AllowUndercut
¶ Returns or sets the undercut
-------------------------------------
Getter Method
Signature
AllowUndercut()
Returns: the undercut Return type: bool New in version NX6.0.0.
License requirements: None.
-------------------------------------
Setter Method
Signature
AllowUndercut(undercut)
Parameters: undercut (bool) – the undercut New in version NX6.0.0.
License requirements: cam_base (“CAM BASE”)
ChipControl¶
-
TurnCutParameters.
ChipControl
¶ Returns the chip control
-------------------------------------
Getter Method
Signature
ChipControl()
Returns: the chip control Return type: NXOpen.CAM.ChipControl
New in version NX6.0.0.
License requirements: None.
CleanupControl¶
-
TurnCutParameters.
CleanupControl
¶ Returns or sets the cleanup control
-------------------------------------
Getter Method
Signature
CleanupControl()
Returns: the cleanup control mode Return type: NXOpen.CAM.CutParametersCleanupControlTypes
New in version NX6.0.0.
License requirements: None.
-------------------------------------
Setter Method
Signature
CleanupControl(cleanupControlValue)
Parameters: cleanupControlValue ( NXOpen.CAM.CutParametersCleanupControlTypes
) – the cleanup control modeNew in version NX6.0.0.
License requirements: cam_base (“CAM BASE”)
ConcaveCornerControl¶
-
TurnCutParameters.
ConcaveCornerControl
¶ Returns the corner concave
-------------------------------------
Getter Method
Signature
ConcaveCornerControl()
Returns: the Concave Corners builder Return type: NXOpen.CAM.TurnConcaveCornerControl
New in version NX6.0.2.
License requirements: cam_base (“CAM BASE”)
ContourDiameterAngle¶
-
TurnCutParameters.
ContourDiameterAngle
¶ Returns the contour diameter angle
-------------------------------------
Getter Method
Signature
ContourDiameterAngle()
Returns: the contour diameter angle Return type: NXOpen.CAM.ContourAngle
New in version NX6.0.0.
License requirements: None.
ContourFaceAngle¶
-
TurnCutParameters.
ContourFaceAngle
¶ Returns the contour face angle
-------------------------------------
Getter Method
Signature
ContourFaceAngle()
Returns: the contour face angle Return type: NXOpen.CAM.ContourAngle
New in version NX6.0.0.
License requirements: None.
ContourLevelAngle¶
-
TurnCutParameters.
ContourLevelAngle
¶ Returns the contour level angle
-------------------------------------
Getter Method
Signature
ContourLevelAngle()
Returns: the contour level angle Return type: NXOpen.CAM.ContourAngle
New in version NX6.0.0.
License requirements: None.
ContourSteepAngle¶
-
TurnCutParameters.
ContourSteepAngle
¶ Returns the contour steep angle
-------------------------------------
Getter Method
Signature
ContourSteepAngle()
Returns: the contour steep angle Return type: NXOpen.CAM.ContourAngle
New in version NX6.0.0.
License requirements: None.
CutConnection¶
-
TurnCutParameters.
CutConnection
¶ Returns or sets the cut connection
-------------------------------------
Getter Method
Signature
CutConnection()
Returns: the cut connection mode Return type: NXOpen.CAM.CutParametersCutConnectionTypes
New in version NX6.0.0.
License requirements: None.
-------------------------------------
Setter Method
Signature
CutConnection(cutConnectionValue)
Parameters: cutConnectionValue ( NXOpen.CAM.CutParametersCutConnectionTypes
) – the cut connection modeNew in version NX6.0.0.
License requirements: cam_base (“CAM BASE”)
CutDwell¶
-
TurnCutParameters.
CutDwell
¶ Returns the Cut Dwell
-------------------------------------
Getter Method
Signature
CutDwell()
Returns: the Cut Dwell Return type: NXOpen.CAM.CutDwell
New in version NX6.0.0.
License requirements: None.
CutFillets¶
-
TurnCutParameters.
CutFillets
¶ Returns or sets the fillets mode
-------------------------------------
Getter Method
Signature
CutFillets()
Returns: the fillets mode Return type: NXOpen.CAM.CutParametersFilletsTypes
New in version NX6.0.0.
License requirements: None.
-------------------------------------
Setter Method
Signature
CutFillets(filletsMode)
Parameters: filletsMode ( NXOpen.CAM.CutParametersFilletsTypes
) – the fillets modeNew in version NX6.0.0.
License requirements: cam_base (“CAM BASE”)
ExtendAtStart¶
-
TurnCutParameters.
ExtendAtStart
¶ Returns or sets the Corner Start Extension
-------------------------------------
Getter Method
Signature
ExtendAtStart()
Returns: the extend at start mode Return type: NXOpen.CAM.CutParametersExtendAtStartMode
New in version NX8.5.0.
License requirements: None.
-------------------------------------
Setter Method
Signature
ExtendAtStart(mode)
Parameters: mode ( NXOpen.CAM.CutParametersExtendAtStartMode
) – the extend at start modeNew in version NX8.5.0.
License requirements: cam_base (“CAM BASE”)
FacesSequence¶
-
TurnCutParameters.
FacesSequence
¶ Returns the Faces Sequence
-------------------------------------
Getter Method
Signature
FacesSequence()
Returns: the faces sequence Return type: NXOpen.CAM.FacesSequence
New in version NX6.0.0.
License requirements: None.
FinishDwell¶
-
TurnCutParameters.
FinishDwell
¶ Returns the finish dwell
-------------------------------------
Getter Method
Signature
FinishDwell()
Returns: the finish dwell Return type: NXOpen.CAM.FinishDwell
New in version NX6.0.0.
License requirements: None.
FinishPasses¶
-
TurnCutParameters.
FinishPasses
¶ Returns or sets the finish passes
-------------------------------------
Getter Method
Signature
FinishPasses()
Returns: the finish passes Return type: NXOpen.CAM.CutParametersFinishPassesTypes
New in version NX6.0.0.
License requirements: None.
-------------------------------------
Setter Method
Signature
FinishPasses(finishPasses)
Parameters: finishPasses ( NXOpen.CAM.CutParametersFinishPassesTypes
) – the finish passesNew in version NX6.0.0.
License requirements: cam_base (“CAM BASE”)
GrooveCornerControl¶
-
TurnCutParameters.
GrooveCornerControl
¶ Returns the groove corner control
-------------------------------------
Getter Method
Signature
GrooveCornerControl()
Returns: the Groove Corner builder Return type: NXOpen.CAM.TurnGrooveCornerControl
New in version NX9.0.0.
License requirements: cam_base (“CAM BASE”)
InitialProfilePlunge¶
-
TurnCutParameters.
InitialProfilePlunge
¶ Returns the initial profile plunge
-------------------------------------
Getter Method
Signature
InitialProfilePlunge()
Returns: the initial profile plunge Return type: NXOpen.CAM.InitialProfilePlunge
New in version NX7.5.0.
License requirements: None.
MinCutDepth¶
-
TurnCutParameters.
MinCutDepth
¶ Returns the min cut depth
-------------------------------------
Getter Method
Signature
MinCutDepth()
Returns: the min cut depth Return type: NXOpen.CAM.MinCutDepth
New in version NX6.0.0.
License requirements: None.
MinCutLength¶
-
TurnCutParameters.
MinCutLength
¶ Returns the min cut length
-------------------------------------
Getter Method
Signature
MinCutLength()
Returns: the min cut depth Return type: NXOpen.CAM.MinCutLength
New in version NX6.0.0.
License requirements: None.
MultiPasses¶
-
TurnCutParameters.
MultiPasses
¶ Returns the multi passes
-------------------------------------
Getter Method
Signature
MultiPasses()
Returns: the multi passes Return type: NXOpen.CAM.StepoverBuilder
New in version NX6.0.0.
License requirements: None.
MultiRamp¶
-
TurnCutParameters.
MultiRamp
¶ Returns the multi ramp
-------------------------------------
Getter Method
Signature
MultiRamp()
Returns: the multi ramp Return type: NXOpen.CAM.MultiRamp
New in version NX6.0.0.
License requirements: None.
NormalCorner¶
-
TurnCutParameters.
NormalCorner
¶ Returns the normal corners
-------------------------------------
Getter Method
Signature
NormalCorner()
Returns: the Normal Corners builder Return type: NXOpen.CAM.TurnCornerControl
New in version NX6.0.0.
License requirements: cam_base (“CAM BASE”)
OmitLastPass¶
-
TurnCutParameters.
OmitLastPass
¶ Returns or sets the omit last pass
-------------------------------------
Getter Method
Signature
OmitLastPass()
Returns: the omit last pass Return type: bool New in version NX6.0.0.
License requirements: None.
-------------------------------------
Setter Method
Signature
OmitLastPass(omitLastPass)
Parameters: omitLastPass (bool) – the omit last pass New in version NX6.0.0.
License requirements: cam_base (“CAM BASE”)
ProfileCutRegions¶
-
TurnCutParameters.
ProfileCutRegions
¶ Returns or sets the profile cut regions
-------------------------------------
Getter Method
Signature
ProfileCutRegions()
Returns: the profile cut regions mode Return type: NXOpen.CAM.CutParametersProfileCutRegionsTypes
New in version NX6.0.0.
License requirements: None.
-------------------------------------
Setter Method
Signature
ProfileCutRegions(profileCutRegionsMode)
Parameters: profileCutRegionsMode ( NXOpen.CAM.CutParametersProfileCutRegionsTypes
) – the profile cut regions modeNew in version NX6.0.0.
License requirements: cam_base (“CAM BASE”)
ProfileDirection¶
-
TurnCutParameters.
ProfileDirection
¶ Returns the direction
-------------------------------------
Getter Method
Signature
ProfileDirection()
Returns: the direction Return type: NXOpen.CAM.TurnDirection
New in version NX6.0.0.
License requirements: None.
ProfileStrategy¶
-
TurnCutParameters.
ProfileStrategy
¶ Returns the cut strategy
-------------------------------------
Getter Method
Signature
ProfileStrategy()
Returns: the cut strategy builder Return type: NXOpen.CAM.ProfileStrategy
New in version NX6.0.0.
License requirements: None.
RampingMode¶
-
TurnCutParameters.
RampingMode
¶ Returns the ramping mode
-------------------------------------
Getter Method
Signature
RampingMode()
Returns: the ramping mode Return type: NXOpen.CAM.RampingMode
New in version NX6.0.0.
License requirements: None.
ReliefCut¶
-
TurnCutParameters.
ReliefCut
¶ Returns the relief cut
-------------------------------------
Getter Method
Signature
ReliefCut()
Returns: the relief cut Return type: NXOpen.CAM.ReliefCut
New in version NX7.5.0.
License requirements: None.
ReliefPlunge¶
-
TurnCutParameters.
ReliefPlunge
¶ Returns the Relief Plunge
-------------------------------------
Getter Method
Signature
ReliefPlunge()
Returns: the Relief Plunge Return type: NXOpen.CAM.ReliefPlunge
New in version NX6.0.0.
License requirements: None.
SecondaryTestCut¶
-
TurnCutParameters.
SecondaryTestCut
¶ Returns the Secondary Test Cut
-------------------------------------
Getter Method
Signature
SecondaryTestCut()
Returns: the Secondary Test Cut Return type: NXOpen.CAM.TurnRoughFinishTestCut
New in version NX8.0.0.
License requirements: None.
ShallowCorner¶
-
TurnCutParameters.
ShallowCorner
¶ Returns the corner shallow
-------------------------------------
Getter Method
Signature
ShallowCorner()
Returns: the Shallow Corners builder Return type: NXOpen.CAM.TurnCornerControl
New in version NX6.0.0.
License requirements: cam_base (“CAM BASE”)
SpringPasses¶
-
TurnCutParameters.
SpringPasses
¶ Returns the spring passes
-------------------------------------
Getter Method
Signature
SpringPasses()
Returns: the spring passes Return type: NXOpen.CAM.SpringPasses
New in version NX6.0.0.
License requirements: None.
StopPosition¶
-
TurnCutParameters.
StopPosition
¶ Returns the stop position
-------------------------------------
Getter Method
Signature
StopPosition()
Returns: the stop position Return type: NXOpen.CAM.StopPosition
New in version NX6.0.0.
License requirements: None.
TestCut¶
-
TurnCutParameters.
TestCut
¶ Returns the Test Cut
-------------------------------------
Getter Method
Signature
TestCut()
Returns: the Test Cut Return type: NXOpen.CAM.TurnRoughFinishTestCut
New in version NX8.0.0.
License requirements: None.
TurnBlankStock¶
-
TurnCutParameters.
TurnBlankStock
¶ Returns the blank stock
-------------------------------------
Getter Method
Signature
TurnBlankStock()
Returns: the blank stock Return type: NXOpen.CAM.TurnStock
New in version NX6.0.0.
License requirements: None.
TurnCutterClearance¶
-
TurnCutParameters.
TurnCutterClearance
¶ Returns the cutter clearance angles
-------------------------------------
Getter Method
Signature
TurnCutterClearance()
Returns: the cutter clearance Return type: NXOpen.CAM.TurnCutterClearance
New in version NX6.0.0.
License requirements: None.
TurnOverlap¶
-
TurnCutParameters.
TurnOverlap
¶ Returns the overlap
-------------------------------------
Getter Method
Signature
TurnOverlap()
Returns: the overlap Return type: NXOpen.CAM.TurnOverlap
New in version NX6.0.0.
License requirements: None.
TurnPartStock¶
-
TurnCutParameters.
TurnPartStock
¶ Returns the part stock
-------------------------------------
Getter Method
Signature
TurnPartStock()
Returns: the part stock Return type: NXOpen.CAM.TurnStock
New in version NX6.0.0.
License requirements: None.
TurnProfileStock¶
-
TurnCutParameters.
TurnProfileStock
¶ Returns the profile stock
-------------------------------------
Getter Method
Signature
TurnProfileStock()
Returns: the profile stock Return type: NXOpen.CAM.TurnStock
New in version NX6.0.0.
License requirements: None.