Represents the Probe Inspect Bore Boss Move Builder More...

Inheritance diagram for NXOpen.CAM.ProbeInspectBorebossMoveBuilder:

Public Types
enum	Angle { Predefined, Custom }
	the angle type More...

enum	Cycle { Bore, Boss }
	the cycle type More...

enum	Depth { Midpoint, Specify }
	the depth type More...

enum	Geometry { Cylinder, Point }
	the geometry type More...

Public Types inherited from NXOpen.CAM.MoveBuilder
enum	Feed { Motion, Custom }
	the feed Type More...

enum	Motion { Rapid = 1, Engage, Cut, Stepover, Retract, Approach, Traversal, Departure, Return, FirstCut, LastCut, Crossover }
	the motion Type More...

Properties
unsafe double	Angle1 `[get, set]`
	Returns or sets the 1st custom angle to probe at More...

unsafe double	Angle2 `[get, set]`
	Returns or sets the 2nd custom angle to probe at More...

unsafe double	Angle3 `[get, set]`
	Returns or sets the 3rd custom angle to probe at More...

unsafe NXOpen.CAM.ProbeInspectBorebossMoveBuilder.Angle	AngleType `[get, set]`
	Returns or sets the angle type More...

unsafe NXOpen.NXObject	ArcVector `[get, set]`
	Returns or sets the arc vector defining the cylinder to inspect More...

unsafe double	BossDimension `[get, set]`
	Returns or sets the radial clearance from nominal target surface More...

unsafe NXOpen.CAM.ExpressionDouble	BossDimensionBuilder `[get]`
	Returns the boss dimension builder More...

unsafe NXOpen.CAM.ProbeInspectBorebossMoveBuilder.Cycle	CycleType `[get, set]`
	Returns or sets the cycle type More...

unsafe NXOpen.NXObject	Cylinder `[get, set]`
	Returns or sets the cylinder to inspect More...

unsafe NXOpen.CAM.ProbeInspectBorebossMoveBuilder.Depth	DepthType `[get, set]`
	Returns or sets the depth type More...

unsafe double	Diameter `[get, set]`
	Returns or sets the diameter defining the cylinder to probe More...

unsafe NXOpen.CAM.ExpressionDouble	DiameterBuilder `[get]`
	Returns the diameter builder More...

unsafe NXOpen.CAM.ProbeInspectBorebossMoveBuilder.Geometry	GeometryType `[get, set]`
	Returns or sets the geometry type More...

unsafe double	MeasurementDepth `[get, set]`
	Returns or sets the probing depth More...

unsafe NXOpen.CAM.ExpressionDouble	MeasurementDepthBuilder `[get]`
	Returns the measurement depth builder More...

unsafe NXOpen.Point	Point `[get, set]`
	Returns or sets the point defining the cylinder to inspect More...

unsafe NXOpen.CAM.ReferencePoint	PointBuilder `[get]`
	Returns the reference point builder More...

unsafe NXOpen.CAM.ProbeControlParametersBuilder	ProbeControlParameters `[get]`
	Returns the probe control parameters builder More...

unsafe NXOpen.CAM.ProbeProtectedParametersBuilder	ProbeProtectedParameters `[get]`
	Returns the probe protected parameters builder More...

unsafe NXOpen.CAM.ProbeStockParametersBuilder	ProbeStockParameters `[get]`
	Returns the probe stock parameters builder More...

unsafe NXOpen.CAM.ProbeToleranceParametersBuilder	ProbeToleranceParameters `[get]`
	Returns the probe tolerance parameters builder More...

Properties inherited from NXOpen.CAM.MoveBuilder
unsafe double	FeedRate `[get, set]`
	Returns or sets the feed rate More...

unsafe NXOpen.CAM.MoveBuilder.Feed	FeedType `[get, set]`
	Returns or sets the feed type More...

unsafe NXOpen.CAM.FeedRateUnit	FeedUnit `[get, set]`
	Returns or sets the feed unit More...

unsafe NXOpen.CAM.MoveBuilder.Motion	MotionType `[get, set]`
	Returns or sets the motion type More...

unsafe int	NumberOfUserParameters `[get]`
	Returns the number of user parameters More...

unsafe bool	ProtectedMove `[get, set]`
	Returns or sets the protected move status More...

unsafe string	SubopLabel `[get, set]`
	Returns or sets the subop label More...

Properties inherited from NXOpen.Builder
unsafe NXOpen.PreviewBuilder	PreviewBuilder `[get]`
	Returns the preview builder subobject. More...

Properties inherited from NXOpen.TaggedObject
Tag	Tag `[get]`
	Returns the tag of this object. More...

Properties inherited from NXOpen.Utilities.NXRemotableObject
IMessageSink	NextSink `[get]`
	Gets the next message sink in the sink chain. More...

Additional Inherited Members
Public Member Functions inherited from NXOpen.CAM.MoveBuilder
unsafe NXOpen.CAM.UdeParameter	GetUserParameter (string parameterName)
	Returns the custom parameter with the given name. More...

unsafe NXOpen.CAM.UdeParameter	GetUserParameter (int index)
	Returns the parameter at the input index. More...

unsafe void	SetParent (NXOpen.CAM.CAMObject parent)
	Set parent More...

unsafe void	SetSibling (NXOpen.CAM.CAMObject sibling)
	Set sibling More...

Protected Member Functions inherited from NXOpen.TaggedObject
new void	initialize ()
	<exclude> More...

Detailed Description

Represents the Probe Inspect Bore Boss Move Builder

To create a new instance of this class, use NXOpen.CAM.MoveCollection.CreateProbeInspectBorebossMoveBuilder

Created in NX5.0.0

Member Enumeration Documentation

enum NXOpen.CAM.ProbeInspectBorebossMoveBuilder.Angle

the angle type

Enumerator
Predefined	Predefined angles
Custom	Custom angles

enum NXOpen.CAM.ProbeInspectBorebossMoveBuilder.Cycle

the cycle type

Enumerator
Bore	Bore
Boss	Boss

enum NXOpen.CAM.ProbeInspectBorebossMoveBuilder.Depth

the depth type

Enumerator
Midpoint	Midpoint of cylinder
Specify	Specify distance

enum NXOpen.CAM.ProbeInspectBorebossMoveBuilder.Geometry

the geometry type

Enumerator
Cylinder	Cylinder
Point	Point

Property Documentation

unsafe double NXOpen.CAM.ProbeInspectBorebossMoveBuilder.Angle1

getset

Returns or sets the 1st custom angle to probe at

Created in NX5.0.0

License requirements to get this property: None.

License requirements to set this property: None.

unsafe double NXOpen.CAM.ProbeInspectBorebossMoveBuilder.Angle2

getset

Returns or sets the 2nd custom angle to probe at

Created in NX5.0.0

License requirements to get this property: None.

License requirements to set this property: None.

unsafe double NXOpen.CAM.ProbeInspectBorebossMoveBuilder.Angle3

getset

Returns or sets the 3rd custom angle to probe at

Created in NX5.0.0

License requirements to get this property: None.

License requirements to set this property: None.

unsafe NXOpen.CAM.ProbeInspectBorebossMoveBuilder.Angle NXOpen.CAM.ProbeInspectBorebossMoveBuilder.AngleType

getset

Returns or sets the angle type

Created in NX5.0.0

License requirements to get this property: None.

License requirements to set this property: None.

unsafe NXOpen.NXObject NXOpen.CAM.ProbeInspectBorebossMoveBuilder.ArcVector

getset

Returns or sets the arc vector defining the cylinder to inspect

Created in NX5.0.0

License requirements to get this property: None.

License requirements to set this property: None.

unsafe double NXOpen.CAM.ProbeInspectBorebossMoveBuilder.BossDimension

getset

Returns or sets the radial clearance from nominal target surface

Created in NX5.0.0

License requirements to get this property: None.

License requirements to set this property: None.

unsafe NXOpen.CAM.ExpressionDouble NXOpen.CAM.ProbeInspectBorebossMoveBuilder.BossDimensionBuilder

get

Returns the boss dimension builder

Created in NX12.0.1

License requirements: None.

unsafe NXOpen.CAM.ProbeInspectBorebossMoveBuilder.Cycle NXOpen.CAM.ProbeInspectBorebossMoveBuilder.CycleType

getset

Returns or sets the cycle type

Created in NX5.0.0

License requirements to get this property: None.

License requirements to set this property: None.

unsafe NXOpen.NXObject NXOpen.CAM.ProbeInspectBorebossMoveBuilder.Cylinder

getset

Returns or sets the cylinder to inspect

Created in NX5.0.0

License requirements to get this property: None.

License requirements to set this property: None.

unsafe NXOpen.CAM.ProbeInspectBorebossMoveBuilder.Depth NXOpen.CAM.ProbeInspectBorebossMoveBuilder.DepthType

getset

Returns or sets the depth type

Created in NX5.0.0

License requirements to get this property: None.

License requirements to set this property: None.

unsafe double NXOpen.CAM.ProbeInspectBorebossMoveBuilder.Diameter

getset

Returns or sets the diameter defining the cylinder to probe

Created in NX5.0.0

License requirements to get this property: None.

License requirements to set this property: None.

unsafe NXOpen.CAM.ExpressionDouble NXOpen.CAM.ProbeInspectBorebossMoveBuilder.DiameterBuilder

get

Returns the diameter builder

Created in NX12.0.1

License requirements: None.

unsafe NXOpen.CAM.ProbeInspectBorebossMoveBuilder.Geometry NXOpen.CAM.ProbeInspectBorebossMoveBuilder.GeometryType

getset

Returns or sets the geometry type

Created in NX5.0.0

License requirements to get this property: None.

License requirements to set this property: None.

unsafe double NXOpen.CAM.ProbeInspectBorebossMoveBuilder.MeasurementDepth

getset

Returns or sets the probing depth

Created in NX5.0.0

License requirements to get this property: None.

License requirements to set this property: None.

unsafe NXOpen.CAM.ExpressionDouble NXOpen.CAM.ProbeInspectBorebossMoveBuilder.MeasurementDepthBuilder

get

Returns the measurement depth builder

Created in NX12.0.1

License requirements: None.

unsafe NXOpen.Point NXOpen.CAM.ProbeInspectBorebossMoveBuilder.Point

getset

Returns or sets the point defining the cylinder to inspect

Created in NX5.0.0

License requirements to get this property: None.

License requirements to set this property: None.

unsafe NXOpen.CAM.ReferencePoint NXOpen.CAM.ProbeInspectBorebossMoveBuilder.PointBuilder

get

Returns the reference point builder

Created in NX12.0.1

License requirements: None.

unsafe NXOpen.CAM.ProbeControlParametersBuilder NXOpen.CAM.ProbeInspectBorebossMoveBuilder.ProbeControlParameters

get

Returns the probe control parameters builder

Created in NX5.0.0

License requirements: None.

unsafe NXOpen.CAM.ProbeProtectedParametersBuilder NXOpen.CAM.ProbeInspectBorebossMoveBuilder.ProbeProtectedParameters

get

Returns the probe protected parameters builder

Created in NX5.0.0

License requirements: None.

unsafe NXOpen.CAM.ProbeStockParametersBuilder NXOpen.CAM.ProbeInspectBorebossMoveBuilder.ProbeStockParameters

get

Returns the probe stock parameters builder

Created in NX5.0.0

License requirements: None.

unsafe NXOpen.CAM.ProbeToleranceParametersBuilder NXOpen.CAM.ProbeInspectBorebossMoveBuilder.ProbeToleranceParameters

get

Returns the probe tolerance parameters builder

Created in NX5.0.0

License requirements: None.

The documentation for this class was generated from the following file:

CAM_ProbeInspectBorebossMoveBuilder.cs

Public Types

Properties

Additional Inherited Members

Detailed Description

Member Enumeration Documentation

Property Documentation