NXOpen .NET Reference Guide
|
Represents a test cut builder More...
Properties | |
unsafe NXOpen.CAM.TurnRoughFinishTestCut.CutTypes | CutType [get, set] |
Returns or sets the test cut type More... | |
unsafe NXOpen.CAM.TurnRoughFinishTestCut.DirectionTypes | Direction [get, set] |
Returns or sets the test cut direction More... | |
unsafe NXOpen.CAM.PostEventsCiBuilder | EndOfTestCut [get] |
Returns the end of test cut More... | |
unsafe NXOpen.CAM.TurnRoughFinishTestCut.FeedInTypes | FeedIn [get, set] |
Returns or sets the test cut feed in More... | |
unsafe double | FeedInAngle [get, set] |
Returns or sets the test cut feed in angle More... | |
unsafe double | FeedInLength [get, set] |
Returns or sets the test cut feed in length More... | |
unsafe NXOpen.CAM.TurnRoughFinishTestCut.FeedOutTypes | FeedOut [get, set] |
Returns or sets the test cut feed out More... | |
unsafe double | FeedOutAngle [get, set] |
Returns or sets the test cut feed out angle More... | |
unsafe double | FeedOutLength [get, set] |
Returns or sets the test cut feed out length More... | |
unsafe NXOpen.Point | MeasuringPoint [get, set] |
Returns or sets the test cut measuring point More... | |
unsafe NXOpen.CAM.TurnRoughFinishTestCut.MeasuringPositionTypes | MeasuringPosition [get, set] |
Returns or sets the test cut measuring position More... | |
unsafe NXOpen.CAM.PostEventsCiBuilder | MeasuringStop [get] |
Returns the measuring stop More... | |
unsafe int | NumberOfPasses [get, set] |
Returns or sets the test cut number of passes More... | |
unsafe NXOpen.CAM.TurnRoughFinishTestCut.ReturnMoveTypes | ReturnMoveOption [get, set] |
Returns or sets the test cut return move More... | |
unsafe NXOpen.Point | ReturnMovePoint [get, set] |
Returns or sets the test cut return move point More... | |
unsafe NXOpen.CAM.PostEventsCiBuilder | SecondaryEndOfTestCut [get] |
Returns the secondary end of test cut More... | |
unsafe NXOpen.CAM.PostEventsCiBuilder | SecondaryMeasuringStop [get] |
Returns the secondary measuring stop More... | |
unsafe NXOpen.CAM.TurnRoughFinishTestCut.SecondarySequenceTypes | SecondarySequence [get, set] |
Returns or sets the secondary test cut sequence More... | |
unsafe NXOpen.CAM.PostEventsCiBuilder | SecondaryStartOfTestCut [get] |
Returns the secondary start of test cut More... | |
unsafe NXOpen.CAM.TurnRoughFinishTestCut.SequenceTypes | Sequence [get, set] |
Returns or sets the test cut sequence More... | |
unsafe NXOpen.CAM.PostEventsCiBuilder | StartOfFinishPass [get] |
Returns the start of finish pass More... | |
unsafe NXOpen.CAM.PostEventsCiBuilder | StartOfTestCut [get] |
Returns the start of test cut More... | |
unsafe double | Stock [get, set] |
Returns or sets the test cut stock More... | |
unsafe NXOpen.CAM.TurnRoughFinishTestCut.StockModeTypes | StockMode [get, set] |
Returns or sets the test cut stock mode More... | |
unsafe double | StopDistance [get, set] |
Returns or sets the test cut stop distance More... | |
unsafe double | StopPercentage [get, set] |
Returns or sets the test cut stop percentage More... | |
unsafe NXOpen.Point | StopPoint [get, set] |
Returns or sets the test cut stop point More... | |
unsafe NXOpen.CAM.TurnRoughFinishTestCut.StopPositionTypes | StopPosition [get, set] |
Returns or sets the test cut stop position More... | |
Properties inherited from NXOpen.TaggedObject | |
Tag | Tag [get] |
Returns the tag of this object. More... | |
Properties inherited from NXOpen.Utilities.NXRemotableObject | |
IMessageSink | NextSink [get] |
Gets the next message sink in the sink chain. More... | |
Additional Inherited Members | |
Public Member Functions inherited from NXOpen.TaggedObject | |
void | PrintTestData (String variableName) |
<exclude> More... | |
void | PrintTestData (String variableName, int lineNumber) |
<exclude> More... | |
override string | ToString () |
Returns a String that represents the current Object. More... | |
Protected Member Functions inherited from NXOpen.TaggedObject | |
new void | initialize () |
<exclude> More... | |
Represents a test cut builder
Created in NX8.0.0
|
getset |
Returns or sets the test cut type
Created in NX8.0.0
License requirements to get this property: None.
License requirements to set this property: cam_base ("CAM BASE")
|
getset |
Returns or sets the test cut direction
Created in NX8.0.0
License requirements to get this property: None.
License requirements to set this property: cam_base ("CAM BASE")
|
get |
Returns the end of test cut
Created in NX8.0.0
License requirements: cam_base ("CAM BASE")
|
getset |
Returns or sets the test cut feed in
Created in NX8.0.0
License requirements to get this property: None.
License requirements to set this property: cam_base ("CAM BASE")
|
getset |
Returns or sets the test cut feed in angle
Created in NX8.0.0
License requirements to get this property: None.
License requirements to set this property: cam_base ("CAM BASE")
|
getset |
Returns or sets the test cut feed in length
Created in NX8.0.0
License requirements to get this property: None.
License requirements to set this property: cam_base ("CAM BASE")
|
getset |
Returns or sets the test cut feed out
Created in NX8.0.0
License requirements to get this property: None.
License requirements to set this property: cam_base ("CAM BASE")
|
getset |
Returns or sets the test cut feed out angle
Created in NX8.0.0
License requirements to get this property: None.
License requirements to set this property: cam_base ("CAM BASE")
|
getset |
Returns or sets the test cut feed out length
Created in NX8.0.0
License requirements to get this property: None.
License requirements to set this property: cam_base ("CAM BASE")
|
getset |
Returns or sets the test cut measuring point
Created in NX8.0.0
License requirements to get this property: None.
License requirements to set this property: cam_base ("CAM BASE")
|
getset |
Returns or sets the test cut measuring position
Created in NX8.0.0
License requirements to get this property: None.
License requirements to set this property: cam_base ("CAM BASE")
|
get |
Returns the measuring stop
Created in NX8.0.0
License requirements: cam_base ("CAM BASE")
|
getset |
Returns or sets the test cut number of passes
Created in NX8.0.0
License requirements to get this property: None.
License requirements to set this property: cam_base ("CAM BASE")
|
getset |
Returns or sets the test cut return move
Created in NX8.0.0
License requirements to get this property: None.
License requirements to set this property: cam_base ("CAM BASE")
|
getset |
Returns or sets the test cut return move point
Created in NX8.0.0
License requirements to get this property: None.
License requirements to set this property: cam_base ("CAM BASE")
|
get |
Returns the secondary end of test cut
Created in NX8.0.0
License requirements: cam_base ("CAM BASE")
|
get |
Returns the secondary measuring stop
Created in NX8.0.0
License requirements: cam_base ("CAM BASE")
|
getset |
Returns or sets the secondary test cut sequence
Created in NX8.0.0
License requirements to get this property: None.
License requirements to set this property: cam_base ("CAM BASE")
|
get |
Returns the secondary start of test cut
Created in NX8.0.0
License requirements: cam_base ("CAM BASE")
|
getset |
Returns or sets the test cut sequence
Created in NX8.0.0
License requirements to get this property: None.
License requirements to set this property: cam_base ("CAM BASE")
|
get |
Returns the start of finish pass
Created in NX8.0.0
License requirements: cam_base ("CAM BASE")
|
get |
Returns the start of test cut
Created in NX8.0.0
License requirements: cam_base ("CAM BASE")
|
getset |
Returns or sets the test cut stock
Created in NX8.0.0
License requirements to get this property: None.
License requirements to set this property: cam_base ("CAM BASE")
|
getset |
Returns or sets the test cut stock mode
Created in NX8.0.0
License requirements to get this property: None.
License requirements to set this property: cam_base ("CAM BASE")
|
getset |
Returns or sets the test cut stop distance
Created in NX8.0.0
License requirements to get this property: None.
License requirements to set this property: cam_base ("CAM BASE")
|
getset |
Returns or sets the test cut stop percentage
Created in NX8.0.0
License requirements to get this property: None.
License requirements to set this property: cam_base ("CAM BASE")
|
getset |
Returns or sets the test cut stop point
Created in NX8.0.0
License requirements to get this property: None.
License requirements to set this property: cam_base ("CAM BASE")
|
getset |
Returns or sets the test cut stop position
Created in NX8.0.0
License requirements to get this property: None.
License requirements to set this property: cam_base ("CAM BASE")